Friday, July 10, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Technical Service Bulletin # 09-08-47-001A Date: 100614

2010 Cadillac CTS Sedan AWD V6-3.0L Technical Service Bulletin # 09-08-47-001A Date: 100614



2010 Cadillac CTS Sedan AWD V6-3.0L Page 252



Body Controls - Unable To Reprogram Body Control Module



INFORMATION



Bulletin No.: 09-08-47-001A



Date: June 14, 2010



Subject: Unable to Reprogram Body Control Module (BCM), BCM Reprogramming Did Not Complete - Revised Reprogramming Instructions



Models:



2006-2010 Buick Lucerne



2006-2010 Cadillac DTS



2007-2010 Cadillac Escalade, Escalade ESV, Escalade EXT, SRX



2008-2010 Cadillac CTS



2010 Cadillac CTS Wagon



2010 Chevrolet Camaro



2006-2007 Chevrolet Monte Carlo



2006-2010 Chevrolet Impala



2007-2010 Chevrolet Avalanche, Equinox, Silverado, Suburban, Tahoe



2008-2010 Chevrolet Express



2009-2010 Chevrolet Traverse



2007-2010 GMC Acadia, Sierra, Yukon, Yukon XL, Yukon Denali, Yukon Denali XL



2008-2010 GMC Savana



2010 GMC Terrain



2007-2009 Pontiac Torrent



2008-2009 Pontiac G8



2008-2009 HUMMER H2



2007-2009 Saturn OUTLOOK



2008-2009 Saturn VUE



Refer to GMVIS



Supercede:



This bulletin is being revised to update the models and the model years. Please discard Corporate Bulletin Number 09-08-47-001 (Section 08 -



Body and Accessories).



Some technicians may experience an unsuccessful body control module (BCM) reprogramming event, when choosing the Reprogram ECU



selection on the Service Programming System (SPS).



The technician may also notice that when attempting to reprogram the BCM again after this incident has occurred, the BCM may not complete the



programming event.



This condition may be caused by the following:



- A reprogramming event that was interrupted due to a lack of communication between the vehicle and the TIS2WEB terminal.



- The vehicle experienced low system voltage during the reprogramming event.



Important



Do not replace the BCM for this condition.



SPS Programming Process Selection



Perform this procedure first.



1. If reprogramming has failed during the initial reprogramming event, back out of the SPS application completely.



2. Re-select SPS from the TIS2WEB terminal application.



3. When selecting the Programming Process , choose Replace and Program ECU , even though a new BCM is NOT being installed.



4. Reprogram the BCM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB. Refer to the SPS



procedures in SI.



When using a multiple diagnostic interface (MDI) for reprogramming, ensure that it is updated with the latest software version.



When using a Tech 2(R) for reprogramming, ensure that it is updated with the latest software version.



During programming, the battery voltage must be maintained within the proper range of 12-15 volts. Only use the approved Midtronics(R) PSC 550



Battery Maintainer (SPS Programming Support Tool EL-49642) or equivalent during programming.



BCM Still Fails to Reprogram



2010 Cadillac CTS Sedan AWD V6-3.0L Page 253



If the BCM still fails to reprogram perform this procedure:



1. Turn OFF the ignition, and remove the key.



2. Remove the fuses that power up the following modules/components for a minimum of 2 minutes:



- BCM



- EBCM



- ECM



- IS LPS (located in the left IP fusebox)



- TCM



3. Open and close the driver door. Allow enough time for the retained accessory power (RAP) to turn OFF.



4. Reinstall the fuses.



5. When selecting the Programming Process , choose Replace and Program ECU , even though a new BCM is NOT being installed.



6. Reprogram the BCM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB. Refer to the SPS



procedures in SI.



When using a multiple diagnostic interface (MDI) for reprogramming, ensure that it is updated with the latest software version.



When using a Tech 2(R) for reprogramming, ensure that it is updated with the latest software version.



During programming, the battery voltage must be maintained within the proper range of 12-15 Volts. Only use the approved Midtronics(R) PSC



550 Battery Maintainer (SPS Programming Support Tool EL-49642) or equivalent during programming.



Warranty Information



For vehicles repaired under warranty, use the table above.