2010 Cadillac CTS Sedan AWD V6-3.0L Page 1741
* Inform the customer that the following actions may cause DTCs P1011, P1012, P1013, or P1014 to set:
- Turning the engine OFF while the accelerator pedal is pressed
- Turning the engine OFF while driving
- Pressing the accelerator pedal to start the engine
* If the customers concern is that the engine is stalling, refer to Symptoms - Engine Controls (See: Powertrain Management/Computers and
Control Systems/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Controls) for further diagnosis.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft
Actuator System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, clear the DTC information with a scan tool.
Note: The engine oil level and the oil pressure are critical to the correct operation of the camshaft position (CMP) actuator system. Verify
that the engine has the correct oil level and the correct oil pressure before continuing with this diagnostic. Refer to Fluid and Lubricant
Recommendations (USA and Canada) (See: Maintenance) and Oil Pressure Diagnosis and Testing (See: Engine, Cooling and
Exhaust/Engine/Testing and Inspection/Component Tests and General Diagnostics/Oil Pressure Diagnosis and Testing) for more information.
2. Start the engine. Verify there is no abnormal engine noise during start up. Observe the DTC information with a scan tool. DTC P1011,
P1012, P1013, or P1014 should not set.
瀚慖f there is an abnormal engine noise, or a DTC set, replace the appropriate CMP actuator.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and
Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake)
* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and
Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust)
* Camshaft Position Actuator Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push
Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 2 (Left Side) Intake)
* Camshaft Position Actuator Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and
Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 2 (Left Side) Exhaust)
