2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1097
K20 ECM.
7. Connect a 3 A fused jumper wire between the signal circuit terminal 4 and the low reference circuit terminal 3. Verify the scan tool HO2S
voltage parameter is less than 60 mV.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the
circuit/connections test normal, replace the K20 ECM.
8. Verify that none of the following conditions exist:
* The HO2S is loose
* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil Test (LF1, LFW) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test).
* Water intrusion in the HO2S harness connector
* Low or high fuel system pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel
System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel
System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery
and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel
Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component
Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).
* Fuel saturation of the evaporative emission (EVAP) canister
* Exhaust leaks near the HO2S
* Engine vacuum leaks
瀚慖f you find any of the above conditions, repair as necessary.
9. If all circuits/connections test normal, replace the B52 HO2S 1.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Sensor 1 (LAU) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Sensor 1)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and
programming
P0133
DTC P0133, P013A, or P013E (Without LF1)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0133
- HO2S Slow Response Sensor 1
DTC P013A
- HO2S Slow Response Rich to Lean Sensor 2
DTC P013E
- HO2S Delayed Response Rich to Lean Sensor 2
Diagnostic Fault Information
