2010 Cadillac Truck SRX AWD V6-2.8L Turbo Technical Service Bulletin # 09-04-95-001D Date: 120716
Drivetrain - Noise Shifting Between Reverse And Drive
TECHNICAL
Bulletin No.: 09-04-95-001D
Date: July 16, 2012
Subject: Clicking Type Noise from Front or Rear of Vehicle When Shifting Between Reverse and Drive or on Hard Acceleration (Add Washer to
Wheel Drive Shaft)
Models:
2010-2011 Buick LaCrosse
2011 Buick Regal
2008-2011 Cadillac CTS, CTS Wagon, Coupe (Includes V Series)
2010-2011 Cadillac SRX
2009-2011 Chevrolet HHR
2010 Chevrolet Camaro Built Prior to June 1, 2009 (V8 Engine (All) and V6 Engine (Manual)) or February 17, 2010 (V6 Engine (Automatic))
2010-2011 Chevrolet Equinox
2011 Chevrolet Cruze
2010-2011 GMC Terrain
Supercede:
This bulletin is being revised to add the HHR model. Please discard Corporate Bulletin 09-04-95-001C (Section 04 - Driveline/Axle).
Condition (Cruze, Equinox, HHR, LaCrosse, Regal, SRX, Terrain)
Some customers may comment on a clicking type noise coming from the front of the vehicle when shifting between reverse and drive or on a hard
acceleration.
Correction (Cruze, Equinox, HHR, LaCrosse, Regal, SRX, Terrain)
Add a washer between the front wheel drive shaft and the bearing hub assembly using the procedure listed below.
Note
- Some vehicles may have been built with the washer. If there is a washer already installed, remove and discard the washer. DO NOT re-use
the washer, replace with NEW only.
- Anytime the wheel drive shaft is separated from the steering knuckle, the washer must be replaced with a NEW washer only.
1. Remove the front wheel bearing and hub assembly. Refer to Front Wheel Bearing and Hub Replacement procedure in SI.
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 28
2. Install the washer (1) onto the front wheel drive shaft (2) as shown above.
Note
For Cruze, Equinox and Terrain, DO NOT reuse wheel drive shaft nut. Discard and replace with a NEW nut only.
3. Install the front wheel bearing and hub assembly. Refer to Front Wheel Bearing and Hub Replacement procedure in SI.
4. Repeat Steps 1 through 3 for the opposite side.
Condition (CTS, Camaro)
Some customers may comment on a clicking type noise coming from the rear of the vehicle when shifting between reverse and drive or on a hard
acceleration.
Correction (CTS, Camaro)
Add a washer between the rear wheel drive shaft and the bearing hub assembly using the procedure listed below.
Note
- Some vehicles may have been built with the washer. If there is a washer already installed, remove and discard the washer. DO NOT re-use
the washer, replace with a NEW washer only.
- Anytime the wheel drive shaft is separated from the steering knuckle, the washer must be replaced with a NEW washer only.
1. Remove the rear wheel bearing and hub assembly. Refer to Rear Wheel Bearing and Hub Replacement procedure in SI.
2. Install the washer (1) onto the rear wheel drive shaft (2) as shown above.
Note
DO NOT reuse wheel drive shaft nut. Discard and replace with a NEW nut only.
3. Install the rear wheel bearing and hub assembly. Refer to Rear Wheel Bearing and Hub Replacement procedure in SI.
4. Repeat Steps 1 through 3 for the opposite side.
Parts Information
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 29
Warranty Information
For vehicles repaired under warranty, use the table.
