2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1181
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Turbocharger System Description (See: Powertrain Management/Fuel Delivery and Air Induction/Turbocharger/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the diagnostic trouble code (DTC) information with a scan tool. Verify that DTCs P0641, P0642, P0643, P2227,
P2228, or P2229 are not set.
瀚慖f any of the above DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.
2. Compare the scan tool BARO parameter to the Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and Control
Systems/Specifications/Altitude Versus Barometric Pressure) table. The BARO should be within the specified range displayed in the table for
the specific altitude.
瀚慖f not within the specified range, refer to DTC P2227, P2228, or P2229 (LAU) (See: P Code Charts/P2227) for further diagnosis.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify the integrity of the entire air induction system including all turbocharger components by inspecting for the following conditions:
* Any damaged components
* Intake air pressure and temperature sensor damage
* A buildup of contamination, snow or ice at the BARO port on the ECM
* Loose or improper installation
* An air flow restriction
* Any vacuum leak
* Any type of air leak between the turbocharger and the throttle body
* An exhaust leak
瀚慖f a condition is found, repair as necessary.
2. Ignition OFF, disconnect the harness connector at the B65 intake air pressure and temperature sensor.
3. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm
between the low reference circuit terminal 1 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20
ECM.
4. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground.
瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the K20 ECM.
瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.
5. Verify the scan tool Boost Pressure Sensor parameter is greater than 250 kPa (36.3 psi).
