Thursday, April 30, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 08-03-10-004A Date: 090724

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 08-03-10-004A Date: 090724



Wheels/Tires - Accessory Wheel And Tire Information



INFORMATION



Bulletin No.: 08-03-10-004A



Date: July 24, 2009



Subject: Mounting, Balancing and Installation of Accessory Wheels and Tires Available Through GM Accessories



Models:



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 257



2010 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn, EXCLUDING Astra)



2003-2010 HUMMER H2



2006-2010 HUMMER H3



Supercede:



This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 08-03-10-004 (Section 03 - Suspension).



This bulletin is intended to offer comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper



methods for mounting, balancing, and installing accessory wheels and tires. Adherence to these methods will ensure that the vehicle delivered to the



customer is of the highest quality.



Tire Pressure Monitor (TPM) Sensor Installation



1. Clean any dirt or debris from the grommet sealing area.



2. Insert the sensor in the wheel hole with the air passage facing away from the wheel



3. Install the sensor nut and position the sensor body parallel to the inside wheel surface while tightening the nut.



Tighten



Tighten the sensor nut to 7 Nm (62 lb in).



Tire Mounting



Important



When mounting the tires, use the approved tire mounting lubricant. DO NOT use silicon or corrosive base compounds to lubricate the tire



bead and the wheel rim. A silicon base compound can allow the tire to slip on the rim resulting in imbalance or braking failure. A corrosive



type compound can cause tire or rim deterioration.



1. Verify that the tire is at least 15掳C (60掳F) prior to mounting and inflating.



2. Apply GM Vehicle Care Rubber Lubricant, P/N 12345884 (Canadian P/N 5728223), to both of the tire beads and both of the wheel bead



hump areas for full circumference.



Important



Mounting operation and wheel assembly must be completed within 15 minutes of applying lubricant to ensure proper assembly and



inflation. Excess lubricant (drips and runs) in the tire must be avoided as it affects balance and may cause tire slippage on wheels



during vehicle operation.



3. Position the rim so the TPM valve stem (1) is situated at the 3 o'clock position relative to the head (2). This will protect the TPM sensor body



by ensuring that the bead is under the least amount of tension when it passes over it.



Important



Some GM Accessory wheels have a "reverse-rim" design and will be marked as such. "Reverse-rim" wheels should be positioned



face-down for tire mounting, taking care not to damage the face of the wheel.



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 258



4. Using the tire changer, rotate the tire/wheel assembly clockwise when transferring the tire bead to the inside of the wheel rim.



5. After the bottom bead is on the wheel, reposition the wheel and tire so that the TPM valve stem is again situated at the 3 o'clock position



relative to the head. This will protect the sensor while mounting the tire bead to the outside of the wheel.



6. Using the tire changer, rotate the tire/wheel assembly clockwise when transferring the tire bead to the inside of the wheel rim.



Danger



To avoid serious personal injury, do not stand over the tire when inflating. The bead may break when the bead snaps over the safety



hump. Do not exceed 40 psi (275 kPa) pressure when inflating any tire if beads are not seated. If 40 psi (275 kPa) pressure will not



seat the beads, deflate, relubricate the beads and reinflate. If greater than 40 psi (275 kPa) is required to install the tire on the wheel,



a safety cage must be used. Overinflation may cause the bead to break and cause serious personal injury.



7. Inflate the tire until it passes the bead humps. Be sure that the valve core is not installed at this time.



8. Install the valve core to the TPM's valve stem.



9. Set the inflation pressure to 40 psi (275 kPa). It will be readjusted to the proper placard pressure when it is installed on the vehicle. This



higher pressure allows for losses due to temperature change or any leakage that may occur prior to installation on the vehicle.



Important



Aggressive accelerating and braking should be avoided for the first 24 hours after the tires have been mounted to avoid the tire slipping on



the rim.



Calibration of Tire/Wheel Balancer



Tire/wheel balancing equipment should be checked for proper calibration every two weeks. Check the calibration of the tire and wheel assembly



balancer according to the manufacturer's recommendations or perform the following test:



Important



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 259



If the balancer fails any of the steps in this calibration test, the balancer should be calibrated according to the manufacturer's



instructions. If the balancer cannot be calibrated, contact the manufacturer for assistance.



1. Spin the balancer without a wheel or any of the adapters on the shaft.



2. Inspect the balancer readings.



Specification



Zero within 0.25 oz (7 g).



3. If the balancer is within the specification range, balance a tire and wheel assembly - that is within radial and lateral runout tolerances - to



ZERO, using the same balancer.



4. After the tire and wheel assembly has been balanced, add a 3 oz (85 g) test weight to the wheel at any location.



5. Spin the tire and wheel assembly again. Note the readings.



- In the static and dynamic modes, the balancer should call for 3 oz (85 g) of weight, 180 degrees opposite the test weight.



- In the dynamic mode, the weight should be called for on the flange of the wheel opposite the test weight.



6. With the assembly imbalanced to 3 oz (85 g), cycle the balancer five times.



7. Inspect the balancer readings:



Specification



Maximum variation: 0.25 oz (7 g).



8. Index the tire and wheel assembly on the balancer shaft 90 degrees from the previous location.



9. Cycle the balancer with the assembly at the new location.



10. Inspect the balancer readings:



Specification



Maximum variation: 0.25 oz (7 g).



11. Repeat Steps 8 through 10 until the tire and wheel assembly has been cycled and checked at each of the 4 locations on the balancer shaft.



Tire and Wheel Balancing



1. Follow the balancer manufacturer's instructions to mount the wheel and tire assembly on the balancer.



2. Perform a dynamic balance on the tire and wheel per the manufacturer's instructions (dynamic balance is sometimes referred to as "couple"



balance). This will indicate the correct amount of balance weight to add at two positions on the wheel.



Adhesive Weight



Clip-On Weight



3. Install a clip-on balance weight on the inboard wheel flange per the weight indications on the balancer.



- Use only MC-series polyester-coated weights at this location. GM Accessory wheels have an MC-rim contour at the inboard location.



- Use only a nylon or plastic tipped hammer to avoid damaging the weight coating or the wheel finish.



- Never strike a wheel weight more than twice. If it doesn't seat properly after two hits, discard it and try a new weight.



Wheel Rim Profile with Adhesive Weight Locations Shown



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 260



Important



Some older GM Accessory wheels may be MC style rims both inboard and outboard and should, therefore, use clip-on MC weights



in both positions. Some GM Accessory wheels may be flangeless on the inboard side. In this case, follow the instructions for applying



adhesive balanced weights. Place the adhesive weight on the face of the rim inner surface, as far inboard as possible (2).



4. Install adhesive balance weights at the outboard location (1) on the wheel per the weight indications on the balancer.



- Both the wheel and the weights must be at least 15掳C (60掳F).



- The area where the weights will be applied must be clean and dry. Wipe the area with a 50/50 mixture, by volume, of isopropyl alcohol



and clean water using a clean cloth. Allow to dry completely.



- Install adhesive weights just inboard of the wheel face on the rim inner surface.



- Apply a force of 21 lb (90 N) to the weights to achieve proper adhesion. This is very important to achieve proper adhesion.



Balance Weight Limits



When dynamically balancing a wheel and tire assembly, the maximum amount of balance weight that should be used at any one location on a wheel



is 5 oz (141 g). This means a maximum of 5 oz (141 g) on the outboard flange (or behind the wheel face, if adhesive weight is used), and maximum



of 5 oz (141 g) on the inboard flange (or on the inner rim surface).



If the balancer calls for greater than 5 oz (141 g) n either position, perform the following steps to reduce the weight:



1. Mark the valve stem location on the tire.



2. Deflate the tire/wheel assembly.



3. Remove any existing balance weights.



4. Rotate tire 180 degrees on the wheel.



5. Re-inflate tire/wheel assembly and rebalance.



6. If the tire/wheel assembly still requires more than 5 oz (141 g) per plane, repeat Steps 1-4, rotating the tire 90 degrees from its original



position.



7. If the tire/wheel assembly still requires more than 5 oz (141 g) per plane, repeat Steps 1-4, rotating the tire 270 degrees from its original



position.



8. If tire/wheel assembly still requires more than 5 oz (141 g) per plane, remove the tire from the wheel, remove all wheel weights and TPM



sensor, and check static balance of the wheel.



Important



This is a static balance check only. The operating mode of the balancer must be changed from "dynamic or couple" to "static". The



balancer should feed back only a single weight value when in static mode.



- If static balance of wheel is 4 oz (113 g) or less, re-use wheel and reject the tire for excessive imbalance.



- If static balance of the wheel is greater than 4 oz (113 g), re-use the tire and reject the wheel for excessive imbalance.



Tire Pressure Monitor Sensor Learn



When installing GM Accessory wheels and tires on a vehicle that have new TPM sensors installed in them, it is necessary to learn the new sensor



identification codes/locations into the vehicle's module. If the relearn procedure is not performed properly, the module will continue to try to



communicate with the original sensors that were removed from the vehicle. This will result in the vehicle displaying a TPM system malfunction



message once the vehicle is removed from the proximity of the original sensors for an extended period of time. Please see the Tire Pressure Sensor



Learn procedure in SI for the vehicle specific instructions.



Tire Inflation Pressure and Placards



Tire Placard



When installing GM Accessory wheels and tires on a vehicle, the new tire pressure placard (supplied with the GM Accessory wheel kit) must be



installed over the existing placard inside the driver's side door frame. This is required when the size of the GM Accessory tires is different than



those being removed from the vehicle.



The new tire placard should be located within the red box, over the top of the original tire label found on the door jamb. To locate the placard



within the red box use the upper left hand edge of the red line as a guide. When properly placed, the new tire placard will obscure the original tire



information. Be sure that the surface is clean and dry, and the surface temperature is not less than 21掳C (65掳F).



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 261



Tire Inflation Pressure



Note the front, rear, and spare (where applicable) tire inflation pressures shown on the new tire placard. The inflation pressure of new tires on the



vehicle must be adjusted to the values shown on the placard. Even if the tire size was not changed on the vehicle and the tire pressure placard was



not replaced, all of the tires must have their inflation pressures adjusted to match those shown on tire pressure placard.



Electronic Module Reprogramming for Proper Tire Inflation Pressure



When GM Accessory wheels and tires are installed on a vehicle that requires a different tire inflation pressure according to the Tire Inflation



Placard, the vehicle must be updated with the new pressure and tire type (P or LT). If this is not done the vehicle will incorrectly report low or high



tire pressure conditions incorrectly. Please see the Corporate Bulletin specific to the vehicle and wheel/tire application for detailed information on



updating of the tire type/pressure.



Other Electronic Module Reprogramming



For proper vehicle operation and to ensure coverage under the provisions of the new vehicle warranty, the vehicle may require that certain control



modules be reprogrammed with the correct calibrations as soon as the GM Accessory wheels and tires are installed. Examples of the modules that



may be affected are Electronic Brake Control Module (for proper anti-lock brake and stability control performance) and Engine Control Module



(for proper speedometer/odometer function).



Please see the Corporate Bulletin specific to the vehicle and wheel/tire application for detailed information on module reprogramming.