Monday, March 9, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1313

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1313



* The engine speed is between 400-5,000 RPM.



* The DTCs run continuously once per crankshaft revolution after the above conditions are met for 20 crankshaft revolutions.



Conditions for Setting the DTC



P0351-P0356



The ECM detects the ignition control circuit is open for greater than 4 seconds or a cumulative of 30 seconds.



P2300, P2303, P2306, P2309, P2312, or P2315



The ECM detects the ignition control circuit is shorted to ground for greater than 4 seconds or a cumulative of 30 seconds.



P2301, P2304, P2307, P2310, P2313, or P2316



The ECM detects the ignition control circuit is shorted to voltage for greater than 4 seconds or a cumulative of 30 seconds.



Action Taken When the DTC Sets



DTCs P0351, P0352, P0353, P0354, P0355, P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, and P2316



are Type B DTCs.



Conditions for Clearing the DTC



DTCs P0351, P0352, P0353, P0354, P0355, P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, and P2316



are Type B DTCs.



Diagnostic Aids



* Inspect the ignition coils for aftermarket devices. An aftermarket device connected to the ignition coil circuits, may cause this DTC to set.



* If the condition is intermittent, moving the related harnesses and connectors, with the engine operating, while monitoring the appropriate scan



tool Misfire Current Cylinder parameter may help to isolate the condition.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic



Ignition System Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Operate the engine for 30 seconds. Observe the DTC information with a scan tool. DTC P0351, P0352, P0353, P0354, P0355, P0356, P2300,



P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 should not set.



2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.