2010 Cadillac CTS Sedan AWD V6-3.6L Page 1836
Conditions for Running the DTC
* Before the ECM can report DTC P2096 or P2098 failed, DTCs P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0056,
P0057, P0058, P013A, P013C, P013E, P0130, P0131, P0132, P0133, P0135, P0137, P0138, P014A, P0140, P0141, P0150, P0151, P0152,
P0153, P0155, P0157, P0158, P0160, P0161, P2232, P2235, P2270, P2271, P2272, and P2273 must run and pass.
* DTC P0100, P0101, P0102, P0103, P0420, P0430, P0442, P0443, P0455, P0458, P0459, P2177, P2178, P2179, P2180, P2187, P2188,
P2189 or P2190 is not set.
* The engine speed is 1,280-3,480 RPM.
* The engine load is 17-65 percent and steady.
* The closed loop fuel control is active for greater than 1 second.
* The calculated exhaust gas temperature is greater than 250掳C (482掳F).
* DTC P2096 and P2098 run continuously when the conditions above have been met for greater than 130 seconds.
Conditions for Setting the DTC
The lean correction limit for a condition causing a rich air/fuel ratio has been exceeded for greater than 4 seconds or for a cumulative of 30 seconds.
Action Taken when the DTC Sets
DTCs P2096 and P2098 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P2096 and P2098 are Type B DTCs.
Diagnostic Aids
An HO2S will not cause this DTC to set without the occurrence of circuit related HO2S DTCs. Do not replace an HO2S to address this DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool DTC information. Verify there is no other HO2S or fuel trim DTC set.
瀚慖f any other HO2S or fuel trim DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Verify that none of the following conditions exist:
* Rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (w/LLT) (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil
Test (w/LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection).
* High fuel system pressure-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and
Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
