Friday, February 21, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1851

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1851



P2187



The Total Fuel Trim Avg. is greater than 40 %, or the long term fuel trim Idle/Decel is greater than 6 %. Either condition exists for 4 s or for a



cumulative of 30 s.



Action Taken When the DTC Sets



DTCs P2177 and P2187 are Type B DTCs.



Conditions for Clearing the MIL/DTC



DTCs P2177 and P2187 are Type B DTCs.



Diagnostic Aids



* A fuel system delivery condition causes this DTC to set. Thoroughly inspect all items that cause a lean condition. Refer to Fuel System



Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System



Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel



Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel System Diagnosis (LAU China) (See: Powertrain



Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis



(LAU Except China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System



Diagnosis (Except China)).



* Any un-metered air into the engine causes this DTC to set. Thoroughly inspect all areas of the engine for vacuum leaks.



* A MAF sensor condition can cause this DTC without setting a MAF DTC. If there is a MAF sensor condition, the MAF sensor parameters



will appear to be within range.



* Inspect the air filter for being the correct one for this application. Make sure that the engine oil fill cap is in place and that it is tight. Verify



that the engine oil dip stick is fully seated.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Observe the DTC information with a scan tool. DTC P2177 or P2187 should not be set.



瀚慖f there are other DTCs set besides DTC P2177 or P2187 refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic



Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) to diagnosis the applicable DTC.



2. Ignition ON, observe the BARO pressure parameter and compare the reading on the scan tool to the barometric pressure table. Refer to



Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and Control Systems/Specifications/Altitude Versus



Barometric Pressure).



瀚慖f the BARO pressure is not within the range specified for your altitude, refer to DTC P2227, P2228, or P2229 (LAU) ( See: P Code