2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2619
* The Trans. Fluid Temp. parameter is between 129-170掳C (264-338掳F).
* The Trans. Fluid Temp. parameter has changed by less than 2.0掳C (3.6掳F) in 100 seconds.
* The ECT is greater than 70掳C (158掳F).
* The ECT has increased by 55掳C (99掳F) since startup.
P0711 - Fail Case 3
The Trans. Fluid Temp. parameter changes by greater than or equal to 20掳C (36掳F) 5 times over 7 seconds.
P0711 - Fail Case 4
* The Trans. Fluid Temp. parameter start up temperature is -50掳C (-58掳F) and does not reach +20掳C (+68掳F) within 3200 seconds.
* The Trans. Fluid Temp. parameter start up temperature is -25掳C (-13掳F) and does not reach +20掳C (+68掳F) within 2600 seconds.
* The Trans. Fluid Temp. parameter start up temperature is -10掳C (-14掳F) and does not reach +20掳C (+68掳F) within 2000 seconds.
* The Trans. Fluid Temp. parameter start up temperature is -5掳C (-23掳F) and does not reach +20掳C (+68掳F) within 1800 seconds.
* The Trans. Fluid Temp. parameter start up temperature is 20掳C (68掳F) and does not reach +20掳C (+68掳F) within 300 seconds.
P0712
The Trans. Fluid Temp. parameter is greater than or equal to 160掳C (320掳F) for greater than 25 seconds.
P0713
The Trans. Fluid Temp. parameter is less than or equal to -60掳C (-76掳F) for greater than 10 seconds.
Action Taken When the DTC Sets
* P0711 is a Type A DTC.
* P0712 and P0713 are Type B DTCs.
* The transmission control module freezes transmission adaptive functions.
Conditions for Clearing the DTC
* P0711 is a Type A DTC.
* P0712 and P0713 are Type B DTCs.
Diagnostic Aids
The driver information center, if equipped, will display 'TRANSMISSION HOT - Idle Engine' when the Trans. Fluid Temp. parameter reaches 132
掳C (270掳F). The Trans. Fluid Temp. parameter on the scan tool should rise steadily to a normal operating temperature, and then stabilize. Ask about
the customer's driving habits, trailer towing, overloading, etc. Ensure the engine and transmission cooling system is functioning normally.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Special Tools
J 24731 Tempil Stick
Circuit/System Verification
Ignition ON, observe the scan tool Trans. Fluid Temp. and the TCM temperature parameters. The readings should vary less than 10掳C (18掳F).
