2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2529
* The scan tool and the terminal must have the latest software.
* The vehicle battery must be fully charged. The battery voltage should be between 12-14 volts.
* The scan tool and the terminal cable connections must be secure.
* A battery charger must NOT be connected to the battery when programming a control module.
2. Ignition ON, with a scan tool verify that DTC P0602 is not set.
瀚慖f DTC P0602 is set, program the transmission control module. Refer to Service Programming System (SPS) (See: Testing and
Inspection/Programming and Relearning/Service Programming System (SPS)) and Control Solenoid Valve and Transmission Control
Module Assembly Programming and Setup (2ML70) (See: Powertrain Management/Transmission Control Systems/Relays and Modules
- Transmission and Drivetrain/Relays and Modules - A/T/Control Module/Testing and Inspection/2ML70 - Automatic Transmission
)Control Solenoid Valve and Transmission Control Module Assembly Programming and Setup (6L45/6L50/6L80/6L90) (See:
Powertrain Management/Transmission Control Systems/Relays and Modules - Transmission and Drivetrain/Relays and Modules -
A/T/Control Module/Testing and Inspection/6L45/6L50/6L80/6L90 - Automatic Transmission).
3. Verify with a scan tool that DTCs P0601, P0603, P0604, or P062F are not set.
瀚慖f DTCs P0601, P0603, P0604, or P062F are set, replace the control solenoid valve and transmission control module assembly.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Programming and Relearning) following all transmission related repairs.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming.
ECM
DTC P0601-P0604, P0606, P0607, P060D, P062F, P16F3, or P2610 (ECM)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provide an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P0607
- Control Module Performance
DTC P060D
- Control Module Accelerator Pedal Position (APP) System Performance
DTC P062F
- Control Module Long Term Memory Performance
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.