2010 Cadillac CTS Sedan AWD V6-3.6L Page 1360
The camshaft position sensor signal voltage is always high and the ECM detects no pulses from the camshaft position sensor for greater than 1 s or
cumulative of 10 s.
Action Taken When the DTC Sets
DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, and P0393 are Type B DTCs.
Diagnostic Aids
The following conditions can also set the DTC:
* Physical damage to the camshaft position sensor or the reluctor wheel
* Excessive play or looseness of the camshaft position sensor or the reluctor wheel
* Improper installation of the camshaft position sensor or the reluctor wheel
* Foreign material passing between the camshaft position sensor and the reluctor wheel
* Excessive air gap between the camshaft position sensor and the reluctor wheel
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft
Actuator System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the DTC information with a scan tool. DTC P0651, P0652 or P0653 should not be set.
瀚慖f a DTC is set, refer to DTC P0641-P0643, P0651-P0653, or P0697-P0699 (ECM, LLT) ( See: P Code Charts/P0641).
2. Engine idling, observe the DTC information with a scan tool. DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368,
P0391, P0392, or P0393 should not set.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, remove the fuse that supplies B+ to terminal 56-X2 of the K20 ECM.
2. Disconnect the harness connector at the appropriate B23 camshaft position sensor.
Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.
3. Test for less than 5 ohm between the low reference circuit terminal 1 and ground.
