* If the Throttle Sweep Test is not available on the scan tool, observe the scan tool TP Sensor 1 and 2 Agree/Disagree parameter while
performing the following tests:
- Slowly depress the accelerator pedal to WOT and then slowly return the pedal to closed throttle. Repeat the procedure several times.
- Rapidly depress the accelerator pedal from the rest position to the wide open throttle position (WOT) and release pedal. Repeat the
procedure several times.
The TP Sensor 1 and 2 Agree/Disagree parameter should display Agree. If Disagree is displayed, continue diagnosis in Circuit/System
Testing.
* A high resistance condition on the throttle position and throttle actuator control circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the DTC information with a scan tool. Verify that DTC P0641 or P0651 are not set.
锟斤拷If a DTC is set, refer to DTC P0641 or P0651 (ECM) (See: P Code Charts/P0641) for further diagnosis.
2. Observe the TP sensor 1 and 2 voltage parameters. Both parameters should be between 1.0-4.0 V and change with accelerator pedal input.
Note: If the Throttle Sweep Test is not available on the scan tool, use the accelerator to perform the test. Refer to Diagnostic Aids for further
details.
3. Perform the Throttle Sweep Test while observing the TP Sensor 1 and 2 Agree/Disagree parameter with a scan tool. The TP Sensor 1 and 2
Agree/Disagree parameter should display Agree.
4. Clear the DTCs with the scan tool. Operate the vehicle within the Conditions for Running the DTC or within the conditions that you observed
from the Freeze Frame/Failure Records.
5. Ignition ON, observe the DTC information with a scan tool. Verify that DTC P0120 or P0220 are not the only TP sensor DTCs set.
锟斤拷If DTC P0120 or P0220 are the only DTCs set, replace the ECM.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the throttle body assembly.
2. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm
between the low reference circuit terminal C and ground.
