2010 Cadillac CTS Sedan AWD V6-3.6L Page 1290
* If the condition is intermittent, observing the scan tool IC Circuit Test and Fuel Injector Circuit Test Status parameters may help isolate the
condition. The circuit test status parameters will change from OK or Not Run to Fault if a condition exists.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* J 26792 - Spark Tester
* For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).
Circuit/System Verification
1. Engine idling at the normal operating temperature.
瀚慖f there is an abnormal engine noise, refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).
2. Verify that no other DTCs are set.
瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble
Code (DTC) List - Vehicle).
3. Observe the scan tool Misfire Current Cyl. 1-6 parameters. The Misfire Current Counters should not be incrementing.
4. Engine idling, perform the cylinder power balance test with a scan tool to isolate the misfiring cylinder. The engine speed should change
when each injector is disabled.
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify that the following conditions do not exist:
* Vacuum hose splits, kinks, and incorrect connections
* Engine vacuum leaks
* Crankcase ventilation system for vacuum leaks
* Fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).
* Contaminated Fuel-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain Management/Computers and
Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with
Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool) (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special
Tool)).
* Exhaust system restrictions
瀚慖f you find any of the above conditions, repair as necessary.
2. Ignition OFF, remove the T8 ignition coil of the misfiring cylinder, but leave the electrical connector connected.
3. Inspect the ignition coil boot for the following conditions:
