2010 Cadillac CTS Sedan AWD V6-3.6L Page 1742
* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/Transmission General Description)
* Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/Transmission Component and System Description)
* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/Electronic Component Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
DT-47825-10 - Jumper Harness
Circuit/System Verification
1. Operate the vehicle in second gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature, then operate the vehicle in Park for 5
seconds.
2. Operate the vehicle in drive range. Allow the transmission to shift through all forward gear ranges. Verify with a scan tool the following test
status parameters display OK:
* Pressure Control Solenoid Valve 3 Performance Test Status
* Pressure Control Solenoid Valve 3 Control Circuit High Voltage Test Status
* Pressure Control Solenoid Valve 3 Control Circuit Low Voltage Test Status
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Ignition OFF, remove the Q8 control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly
Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and
Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).
2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/Control Solenoid Valve and Transmission Control
Module Assembly Inspection).
3. Place the Q8 control solenoid valve assembly on a clean work surface near the transmission assembly.
4. Connect DT-47825-10 - jumper harness between the vehicle wire harness electrical connector, and the Q8 control solenoid valve assembly
electrical connector.
5. Ignition ON, verify with a scan tool the following test status parameters display OK:
* Pressure Control Solenoid Valve 3 Performance Test Status
* Pressure Control Solenoid Valve 3 Control Circuit High Voltage Test Status
* Pressure Control Solenoid Valve 3 Control Circuit Low Voltage Test Status
瀚慖f any test status parameter displays Fault or Malfunction, replace the Q8 control solenoid valve assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Solenoid Valve and Transmission Control Module Assembly Cleaning (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/Control Solenoid Valve and Transmission Control
Module Assembly Cleaning)
* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
