DTC B0022, B0024, B0026, B0042, B0043, OR B0044
Circuit Description
The driver frontal deployment loop consists of the following components:
l A dual stage inflatable restraint steering wheel module
l The inflatable restraint steering wheel module coil
l The steering wheel module high circuits for both stages 1 and 2
l The steering wheel module low circuits for both stages 1 and 2
There are 2 shorting bars used within the steering wheel module coil connector which will short together both the steering wheel module stage 1 high circuit and the steering wheel module stage 1 low circuit, and both the steering wheel module stage 2 high circuit and the steering wheel module stage 2 low circuit, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. During a frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop, in order to deploy the steering wheel module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
l DTC B0022 Driver Frontal Deployment Loop (Stage 1) Resistance Low
l DTC B0024 Driver Frontal Deployment Loop (Stage 1) Voltage Out of Range
l DTC B0026 Driver Frontal Deployment Loop (Stage 1) Open
l DTC B0042 Driver Frontal Deployment Loop (Stage 2) Resistance Low
l DTC B0043 Driver Frontal Deployment Loop (Stage 2) Voltage Out of Range l DTC B0044 Driver Frontal Deployment Loop (Stage 2) Open
Conditions for Running the DTC
Ignition 1 voltage is within the normal operating voltage range.
Conditions for Setting the DTC
l DTC B0022 stage 1 or B0042 stage 2 will set when the steering wheel module deployment loop resistance is less than 1.3 ohms for 500 milliseconds. l DTC B0024 stage 1 or B0043 stage 2 will set when one of the following conditions occur: . The steering wheel module high and/or low circuits are shorted to ground or shorted to voltage for 500 milliseconds.
. The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop resistance is less than 6 ohms for 500 milliseconds.
l DTC B0026 stage 1 or B0044 stage 2 will set when one of the following conditions occurs:
. The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop is more than 6 ohms for 500 milliseconds.
. The steering wheel module deployment loop resistance is more than 4.8 ohms for 500 milliseconds.
Action Taken When the DTC Sets
The SDM commands the AIR BAG indicator ON via class 2 serial data.
Conditions for Clearing the DTC
l The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used. l A history DTC will clear once 255 malfunction-free ignition cycles have occurred.
Diagnostic Aids
The following are possible causes of the malfunction:
l A short between the steering wheel module stage 1 or stage 2, high and low circuits l An open or a high resistance in the steering wheel module stage 1 or stage 2, high or low circuits l A short to ground or a short to voltage in the steering wheel module stage 1 or stage 2, high or low circuits l The steering wheel module coil connector
l The SDM connector
l A malfunctioning steering wheel module
l A malfunctioning steering wheel module coil
l A malfunctioning SDM
Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
5: This step tests to see if the malfunction is caused by the steering wheel module or by the steering wheel module coil.
7: This step tests to see what DTCs are present. If DTC B0022 or B0042 is present, test the steering wheel module for a short between high and low circuits in stage 1 or stage 2. If DTC B0024 or B0043 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2. If DTC B0026 or B0044 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2.
DTC B0022, B0024, B0026, B0042, B0043, or B0044
Step Action Yes No
Schematic Reference: SIR Schematics Connector End View Reference: SIR Connector End Views
1 Did you perform the Diagnostic System Check -Vehicle? Go to Step 2 Go to Diagnostic System Check -Vehicle
2 1. Turn OFF the ignition. 2. Disconnect the steering wheel module coil inline connector. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement. 3. Inspect the component and harness sides of the inline connector for the steering wheel module coil for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Does connector exhibits any signs of damage or corrosion? Go to Step 3 Go to Step 4
1. If the inline connector for the steering wheel module coil is damaged,
3
4
5 6
the steering wheel module coil must be
replaced. Refer to Inflatable
Restraint Steering Wheel Module Coil
Replacement.
2. If the wiring harness side of steering
wheel module coil inline connector is -
damaged, replace the harness side of
the connector. Refer to Connector
Repairs .
Did you complete the repair? Go to Step 11
IMPORTANT:
If the scan tool displays multiple codes,
diagnose the open code first.
1. Use the J 38715-80 Adapter to connect
the J 38715-A SIR Driver/Passenger
Load Tool to the harness side of the
steering wheel module coil connector.
Use the base of column and passenger
inflator connectors.
2. Turn ON the ignition, with the engine
OFF.
3. Use the scan tool to request SIR DTCs
displayed.
Does the scan tool indicate that DTC B0022,
B0024, B0026, B0042, B0043, or B0044 are
current? Go to Step 6 Go to Step 5
1. Turn OFF the ignition.
2. Disconnect and remove both the J
38715-A and adapter.
3. Connect the steering wheel module coil
inline connector.
4. Remove the steering wheel module.
Refer to Inflatable Restraint Steering
Wheel Module Replacement.
5. Use the J 38715-120 Adapter to connect
the J 38715-A to the upper steering
wheel module coil connector on top of
the steering column. Use the steering
column and passenger inflator
connectors.
6. Turn ON the ignition, with the engine
OFF.
7. Use the scan tool to request SIR DTCs
displayed.
7
8
