2010 Cadillac CTS Sedan AWD V6-3.6L Page 777

2010 Cadillac CTS Sedan AWD V6-3.6L Page 777

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the EBCM.

5. Ignition OFF, disconnect the X1 harness connector at the EBCM.

6. Ignition OFF, test for infinite resistance between the signal circuit terminal 21 and ground.

瀚慖f not the specified value, test the signal circuit for a short to ground.

7. If all circuits test normal, test or replace the power brake booster vacuum sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay

Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power

Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup and programming

P000A

DTC P000A-P000D, P0011, P0014, P0021, or P0024 (Without LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P000A

- Intake Camshaft Position System Slow Response Bank 1

DTC P000B

- Exhaust Camshaft Position System Slow Response Bank 1

DTC P000C

- Intake Camshaft Position System Slow Response Bank 2

DTC P000D

- Exhaust Camshaft Position System Slow Response Bank 2

DTC P0011

- Intake Camshaft Position System Performance Bank 1

DTC P0014

- Exhaust Camshaft Position System Performance Bank 1

DTC P0021

- Intake Camshaft Position System Performance Bank 2

DTC P0024

- Exhaust Camshaft Position System Performance Bank 2

Circuit/System Description

The camshaft position actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is

operating. The camshaft position actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the camshaft position

actuator solenoid duty cycle by controlling the amount of solenoid ON time. The camshaft position actuator solenoid controls the advance or the

retard of each camshaft. The camshaft position actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.

Conditions for Running the DTC

* Before the ECM can report DTC P000A, P000B, P000C, P000D, P0011, P0014, P0021, or P0024 failed, DTCs P0010, P0013, P0020,

P0023, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089, P2090, P2091, P2092,

P2093, P2094, and P2095 must run and pass.

* DTC P0016, P0017, P0018, P0019, P0335, P0336, or P0338 is not set.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2987

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2987

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2154

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2930

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2930

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2126

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac CTS Sedan AWD V6-3.6L Page 703

2010 Cadillac CTS Sedan AWD V6-3.6L Page 703

replace the EBCM.

6. If all circuits test normal, replace the yaw/lateral accelerometer sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup and programming

C0292

DTC C0292

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC C0292 02

- VSES Combination Sensor Circuit Short to Ground

DTC C0292 07

- VSES Combination Sensor Circuit Voltage Above Threshold

Circuit/System Description

The electronic brake control module (EBCM) supplies a ignition voltage to the yaw rate sensor/lateral acceleration sensor, and the steering angle

sensor. The sensor supply voltage is monitored via an internal feedback circuit to the EBCM microprocessor.

Conditions for Running the DTC

* Ignition ON.

* Ignition voltage is greater than 10 volts.

Conditions for Setting the DTC

The EBCM detects a short to ground or an open/high resistance on the sensor supply voltage

Actions Taken when the DTC Sets

* The EBCM disables StabiliTrak for the duration of the ignition cycle.

* A DIC message and/or a warning indicator may be displayed.

Conditions for Clearing the DTC

* The condition for the DTC is no longer present.

* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation)

Electrical Information Reference

2010 Cadillac Truck Escalade RWD V8-6.2L Page 3044

2010 Cadillac Truck Escalade RWD V8-6.2L Page 3044

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2199

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2987

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2987

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2154

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2930

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2930

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2126

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 3044

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 3044

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2199

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade AWD V8-6.2L Page 3159

锟斤拷If greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2199

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade AWD V8-6.2L Page 3102

锟斤拷If greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2154

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade AWD V8-6.2L Page 3045

锟斤拷If greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2126

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 839

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 839

4. If all circuits test normal, replace the EBCM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming

C12D0

DTC C056D, C120C, C121C, C121E, C121F, C123A-C1256, C126E-C127C, C12C2-C12DB, C12DE, C12DF, or C12F2-C12F6

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

DTC Descriptors

DTC C056D 00

- ECU Hardware Performance

DTC C056D 3C

- ECU Hardware Performance Internal Communications Failure

DTC C056D 59

- ECU Hardware Performance

DTC C120C

- Brake Pedal Position Sensor 4 Plausibility

DTC C121C

- EBCM Internal Communication Error

DTC C121E

- EBCM Unimplemented Interrupt

DTC C121F

- EBCM Unexpected Exception

DTC C123A

- EBCM High End Timer Watchdog

DTC C123B

- EBCM High End Timer Program Overflow

DTC C123C

- EBCM High End Timer RAM Fault

DTC C123D

- EBCM Solenoid Timeout

DTC C123E

- EBCM High End Timer Periodic Interrupt

DTC C123F

- EBCM Serial Peripheral Interface Inoperative

DTC C1255

- Electronic Control Unit Performance

DTC C1256

- Program ROM Checksum Error

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3159

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3159

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2199

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3102

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3102

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2154

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The vehicle power mode master requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

* The vehicle stability enhancement system (VSES), if equipped, and traction control system (TCS) will not function.

* System OFF lamps will illuminate for these systems.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.