DTC P0218
- Transmission Fluid Overtemperature
Circuit/System Description
The primary source of heat in the transmission is the drive motor generators. The drive motor generators are cooled by the transmission fluid. Hot
fluid exits the drive motor generators and flows to the transmission fluid cooler pipe assembly. The transmission fluid cooler pipe assembly
connects to the cooler, which is in front of the radiator. The transmission fluid cooler pipe assembly is equipped with an internal thermostat that
opens at 80锟斤拷C (176锟斤拷F) for optimum transmission operation and fuel economy. The transmission fluid cooler pipe thermostat is part of the
transmission fluid cooler pipe assembly, located near the transmission and is not serviced separately. From the cooler, the fluid returns through the
transmission fluid cooler pipe assembly and enters the lubrication circuits. After lubricating the internal components, the fluid returns to the oil pan.
The sensor is located in the control solenoid valve assembly and is not serviced separately.
Conditions for Running the DTC
The transmission fluid temperature is at least -50 (-58锟斤拷F) and no more than +150锟斤拷C (+302锟斤拷F) for 5 seconds.
Conditions for Setting the DTC
The transmission fluid temperature is greater than 135锟斤拷C (275锟斤拷F) for 300 seconds.
Action Taken When the DTC Sets
* P0218 is a Type B DTC.
* The driver information center may display 'TRANSMISSION HOT - Idle Engine'.
Conditions for Clearing the DTC
P0218 is a Type B DTC.
Diagnostic Aids
* The driver information center will display 'TRANSMISSION HOT- Idle Engine' with an audible chime when the transmission fluid
temperature is greater than 150锟斤拷C (302锟斤拷F). The message and chime will not turn off until the transmission fluid temperature is less than 150锟斤拷
C (302锟斤拷F) and the ignition is Off long enough for the TCM to power down.
* Ask about the customer's driving habits, trailer towing, etc.
* Verify the engine cooling system is functioning normally.
* The hybrid powertrain control module will reduce drive motor generator torque at temperatures greater than 160锟斤拷C (320锟斤拷F). Drive motor
generator torque is reduced to zero if the temperature reaches 190锟斤拷C (374锟斤拷F).
* Review with the customer their driving habits, trailer towing, etc. Verify the engine cooling system and transmission cooling system is
functioning normally.
Reference Information
Description and Operation
Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/2ML70 -
Automatic Transmission/Electronic Component Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
1. Verify that P0711, P0712, or P0713 is not set.
锟斤拷If DTC P0711, P0712, or P0713 is set, Refer to DTC P0711, P0712, or P0713 ( See: P Code Charts/P0711/2ML70 - Automatic
Transmission).
2. Ignition ON, observe the scan tool ECM engine coolant temperature (ECT) parameter in the freeze frame data. The reading should be below
125锟斤拷C (257锟斤拷F).
锟斤拷If the ECT was above 125锟斤拷C (257锟斤拷F) when the DTC set, refer to Engine Overheating (See: Engine, Cooling and Exhaust/Cooling
System/Testing and Inspection/Symptom Related Diagnostic Procedures/Engine Overheating).
3. Ignition ON, observe the scan tool Trans. Fluid Temp. parameter in the freeze frame data. The reading should be below 135锟斤拷C (275锟斤拷F).