2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 593
Action Taken When the DTC Sets
The heated seat cushion function for the affected seat will be disabled.
Conditions for Clearing the DTC
* The current DTC clears when the malfunction is no longer present, and the power mode changes to OFF then back to ACC or RUN.
* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.
Reference Information
Schematic Reference
Heated/Cooled Seat Schematics ()
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
B2425 0A, B2425 0B, B2425 0C, B2425 0D, B2425 0E, B2425 04, or B2425 1F
1. Ignition OFF, disconnect the X1 harness connector at the HSM.
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 2.0 - 8.0 Ohms between control circuit terminal 3 and control circuit terminal 5.
锟斤拷If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
锟斤拷If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the seat cushion
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 9 X4 and the low reference circuit terminal 6 X2.
锟斤拷If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
锟斤拷If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
锟斤拷If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
锟斤拷If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
8. If all circuits test normal, replace the HSM.
B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F
1. Ignition OFF, disconnect the X1 harness connector at the HSM.
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.