2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1755
* Observe the DTC information with a scan tool. Verify there are no B52 HO2S heater or fuel trim DTCs set.
锟斤拷If any DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic
Trouble Code (DTC) List - Vehicle).
* Engine idling at operating temperature, observe the appropriate B52 HO2S parameter with a scan tool. Verify the following:
- The B52 HO2S 1 value should vary from below 200 mV to above 800 mV and respond to fueling changes.
- The B52 HO2S 2 value should change greater than 200 mV when the throttle is quickly cycled 3 times from closed to wide open and
back to closed after running the engine at 1,500 RPM for 30 s.
* Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify none of the following conditions exist:
* Lean or rich fuel injectors-Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See: Powertrain Management/Fuel
Delivery and Air Induction/Fuel Injector/Testing and Inspection)
* Water intrusion in the B52 HO2S harness connector
* Low or high fuel system pressure-Refer to Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics)
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (
See: Powertrain Management/Fuel Delivery and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis
(Special Tool))
* Fuel saturation of the evaporative emission (EVAP) canister
* Exhaust leaks near the B52 HO2S
* Engine vacuum leaks
* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis)
* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and
Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant)
锟斤拷If you find any of the above conditions, repair as necessary.
2. If all conditions test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P15F0
DTC P15F0
Diagnostic Instructions
