2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 590
4. Test for 2.0 - 8.0 Ohms between control circuit terminal 14 and control circuit terminal 11.
锟斤拷If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
锟斤拷If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the seat cushion
heater element.
5. Disconnect the X2, X5 harness connectors at the MSM.
6. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 1 X5 and the low reference circuit terminal 3 X2.
锟斤拷If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
锟斤拷If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
7. Connect the X1, X2, X5 harness connectors at the MSM.
8. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
9. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
锟斤拷If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
锟斤拷If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
10. If all circuits test normal, replace the MSM.
B2430 0A, B2430 0B, B2430 0C, B2430 0D, B2430 0E, B2430 04, or B2430 1F
1. Ignition OFF, disconnect the X3 harness connector at the MSM.
2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 5 and ground.
锟斤拷If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the X3 harness connector at the MSM and disconnect the X1, X4 harness connectors at the MSM.
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
4. Test for 2.0 - 8.0 Ohms between control circuit terminal 6 X1 and control circuit terminal 14 X4.
锟斤拷If less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
锟斤拷If greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal replace the seat cushion
heater element.
5. Disconnect the X2, X5 harness connectors at the MSM.
6. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
锟斤拷If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
锟斤拷If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
7. Connect the X1, X2, X4, X5 harness connectors at the MSM.
8. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
9. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
锟斤拷If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
锟斤拷If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
10. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
